微型化半球陀螺制备工艺发展现状及趋势分析

因低噪声、高性能、无磨损的优势，半球陀螺已成为航空、航天领域内的最佳导航陀螺。半球陀螺的微型化是微机电陀螺领域的研究热点，全球各研究单位设计了多种形态的谐振器结构，开发了各具特色的加工工艺，其选用的材质也各不相同，并研制出了形态各异的微半球陀螺结构。对半球陀螺微型化的历程和方式进行了综述，着重对微型化半球陀螺壳体谐振器的结构形态、工艺制备方法和选材进行了对比和分析，并对各微型化途径的特点进行了讨论和展望。     

基于HHT的航空直流串行电弧特征提取方法

由于飞机内部布线空间有限、电弧故障存在发生时间地点随机以及特征不明显等问题，导致检测困难。本文基于航空270 V高压直流（HVDC）系统开展直流串行电弧故障特征提取方法研究，采用希尔伯特黄变换（HHT）提取电弧电流交流分量的时域和频域特征量。选择HHT的固有模态函数IMF5瞬时幅值的峰峰值和标准差作为识别电弧故障的时域特征，与原始信号中提取的时域特征量对比，正常和电弧特征量的区分度更大；选择HHT的固有模态函数IMF1+IMF2、一定频带范围内的瞬时幅值计算得到的谐波功率和作为区分正常和电弧情况的频域特征量。与常用的快速傅里叶变换（FFT）方法相比，HHT三维时频谱能够反映信号的局部特征，HHT方法计算得到的正常和电弧特征量之间的区分度更大，电弧和正常特征量的比值最高可达346。基于HHT的电弧故障特征提取方法能够更好地区分正常和电弧情况，有助于提高电弧故障的检测率，降低虚警率，具有重要的工程应用价值。     

某航天器输氢管道系统结构完整性评估

为保障某航天器在服役年限内不发生事故，针对航天器上采用插入焊接技术的精密管道系统进行结构完整性评估。在考虑到系统存在整圈的环形未焊透缺陷基础上，结合工程实践，假设在焊接区域存在更危险的平面缺陷。首先，开展高压气相热充氢试验下的标准拉伸和三点弯试验得到管道系统材料"J-75"在临氢环境下应力应变曲线和断裂韧性。其次，采用有限元程序计算系统在内压、惯性载荷与离面位移作用下的应力分布，考虑到间隙配合中的不确定性，改变模型中的最大间隙多次模拟计算，发现最大应力位置基本不变，以此区域作为假想缺陷的具体萌生区域。最后，采用失效评估图（FAD）方法对存在4种缺陷模式的系统分别进行结构完整性评估。通过引入安全裕度的概念，发现系统在含有初始尺寸（0.15 mm）的4种平面缺陷时，均处于安全状态，并且安全裕度都在2倍以上；通过工程临界分析（ECA）发现随着缺陷尺寸的增大，系统中含有缺陷2（位于管道焊接区域最大应力处的轴对称平面且沿焊深方向扩展的缺陷）时最为危险，且当缺陷深度超过0.61 mm时将断裂失效；考虑到测试数据的弥散性，针对系统最危险的模式，以安全裕度为可靠性指标，将失效评估图方法与可靠性评价相结合，得到系统在含有尺寸为0.15 mm的缺陷2情况下保有足够安全裕度的可靠性下限值超过0.999 5。     

过氧化氢/紫外线/臭氧氧化技术处理肼类污水的应用

采用放大试验规模（处理量1 m³/h）的H₂O₂（过氧化氢）/UV（紫外线）/O₃（臭氧）氧化技术处理肼类推进剂污水，在30.0±1.6 ℃，pH=9.0±0.2的条件下，研究肼类的过氧化氢增强光解臭氧化降解。对比不同氧化技术的协同效应以及对污水降解的影响，重点考察过氧化氢、紫外线、臭氧和初始浓度等工艺参数对降解效果的影响，对氧化技术的应用进行了优化。研究结果表明：该技术可使COD去除率提高27.66%，肼类的降解速率随着过氧化氢投加量、紫外线辐射强度、O₃投加速率和水质地提高而升高，随着初始质量浓度的提高而下降。在最佳工艺下，处理5 000 mg/L质量浓度的废水，处理60 min时，COD去除率分别为98.62%（偏二甲肼）、99.17%（甲基肼）、99.94%（肼）和93.25%（单推-3）。     

空天飞行器返回滑翔段在线制导方法

针对空天往返飞行器的返回滑翔段在线制导问题，设计了一种新的滑翔段飞行剖面，实现了滑翔段终端交班高度、位置和倾角约束的自动满足，减少了在线制导算法中需处理的约束数量。推导了滑翔段运动状态、过程约束和性能指标的解析表达式，获得了剩余航程和终端速度间的函数关系。在此基础上，提出了一种双层在线制导方法：内层解析重构飞行剖面，同时通过解析确定路径点来改变剩余航程的变化率，进而对终端交班速度进行控制；外层借助解析表达式，使用粒子群优化算法(PSO)和改进共轭梯度法(CGM)优化飞行剖面，从而满足过程约束和指标要求。最后通过数学仿真验证了方法的正确性。     

基于听觉感知的驾驶舱信息提示设计研究

为研究飞机驾驶舱中不同的听觉信息提示方式对感知效率、关注程度影响差异,基于飞行仿真场景构建飞行任务,在任务执行中提供听觉刺激提示,采集被试任务全过程中的脑电信号并进行了时域和频域维度的分析,对比语言听觉/非语言听觉以及不同播报速度的工效影响,总结了被试对驾驶舱听觉信息提示的反应特征,为听觉信息提示的人机交互设计提供参考建议.     

Evaluation of SARAL/AltiKa performance using GNSS/IMU equipped buoy in Sajafi,Imam Hassan and Kangan Ports

Performance of SARAL/AltiKa mission has been evaluated within 2016 altimeter calibration/validation framework in Persian Gulf through three campaigns conducted in the offshore waters of Sajafi, Imam Hassan and Kangan Ports, while the altimeter overflew the passes 470, 111 and 25 on 13 Feb, 7 March and 17 June 2016, respectively. As the preparation, a lightweight buoy was equipped with a GNSS receiver/choke-ring antenna and a MEMS-based IMU to measure independent datasets in the field operations. To obtain accurate sea surface height (SSH) time series, the offset of the onboard antenna from the equilibrium sea level was predetermined through surveying operations as the buoy was deploying in the onshore waters of Kangan Port. Accordingly, the double-difference carrier phase observations have been processed via the Bernese GPS Software v. 5.0 so as to provide the GNSS-derived time series at the comparison points of the calibration campaigns, once the disturbing effects due to the platform tilt and heave have been eliminated. Owing to comparing of the SSH time series and the associating altimetry 1?Hz GDR-T datasets, the calibration/validation of the SARAL/AltiKa has been performed in the both cases of radiometer and ECMWF wet troposphere corrections so as to identify potential land contamination. An agreement of the present findings in comparison with those attained in other international calibrations sites confirms the promising feasibility of Persian Gulf as a new dedicated site for calibration/validation of ongoing and future altimetry missions.     

Application of Wuhan Ionospheric Oblique Backscattering Sounding System (WIOBSS) for the investigation of midlatitude ionospheric irregularities

An upgrade of Wuhan Ionospheric Backscattering Sounding System (WIOBSS) was developed in 2015. Based on the Universal Serial Bus (USB), and a high performance FPGA, the newly designed WIOBSS has a completely digital structure, which makes it portable and flexible. Two identical WIOBSSs, which were situated at Mile (24.31°N, 103.39°E) and Puer (22.74°N, 101.05°E) respectively, were used to investigate the ionospheric irregularities. The comparisons of group distance, Doppler shift and width between Mile-Puer and Puer-Mile VHF ionospheric propagation paths indicate that the reciprocity of the irregularities is satisfied at midlatitude region. The WIOBSS is robust in the detection of ionospheric irregularities.     

Comparison of GPS derived TEC with the TEC predicted by IRI 2012 model in the southern Equatorial Ionization Anomaly crest within the Eastern Africa region

We have compared the TEC obtained from the IRI-2012 model with the GPS derived TEC data recorded within southern crest of the EIA in the Eastern Africa region using the monthly means of the 5 international quiet days for equinoxes and solstices months for the period of 2012 – 2013. GPS-derived TEC data have been obtained from the Africa array and IGS network of ground based dual-frequency GPS receivers from four stations (Kigali (1.95°S, 30.09°E; Geom. Lat. 11.63°S), Malindi (2.99°S, 40.19°E; Geom. Lat. 12.42°S), Mbarara (0.60°S, 30.74°E; Geom. Lat. 10.22°S) and Nairobi (1.22°S, 36.89°E; Geom. Lat. 10.69°S)) located within the EIA crest in this region. All the three options for topside Ne of IRI-2012 model and ABT-2009 for bottomside thickness have been used to compute the IRI TEC. Also URSI coefficients were considered in this study. These results are compared with the TEC estimated from GPS measurements. Correlation Coefficients between the two sets of data, the Root-Mean Square Errors (RMSE) of the IRI-TEC from the GPS-TEC, and the percentage RMSE of the IRI-TEC from the GPS-TEC have been computed. Our general results show that IRI-2012 model with all three options overestimates the GPS-TEC for all seasons and at all stations, and IRI-2001 overestimates GPS-TEC more compared with other options. IRI-Neq and IRI-01-corr are closely matching in most of the time. The observation also shows that, GPS TEC are underestimated by TEC from IRI model during noon hours, especially during equinoctial months. Further, GPS-TEC values and IRI-TEC values using all the three topside Ne options show very good correlation (above 0.8). On the other hand, the TEC using IRI-Neq and IRI-01- corr had smaller deviations from the GPS-TEC compared to the IRI-2001.     

单向电永磁作动器结构优化与动态特性分析

针对电磁作动器的使用要求，设计出一种具有能耗低、吸力大及响应快等特点的新型单向电永磁作动器。结合有限元仿真软件，利用有限元法研究作动器的结构参数如铁芯齿形结构、平面结构、无永磁结构、铁芯的倾斜角度及衔铁位移（气隙厚度）等因素对作动器电磁吸力和响应速度的影响。结果表明，电磁吸力随着作动衔铁位移的增加而大幅度减小；倾角结构的铁芯设计能使作动器性能达到最佳，且铁芯的倾斜角度为50°时，电磁吸力有最大值3071N。